滩地造林抑螺作用机理研究进展

长江流域滩地是我国钉螺分布的主要区域，也是血吸虫病的主要流行区。近些年我国大力实施的林业血防工程通过滩地营造人工杨树林，使得钉螺原有孳生地的多种生物要素和非生物要素发生了明显变化，显著减少了钉螺种群的分布空间，从而有效控制了血吸虫病的传播。目前，国内外在滩地造林后单一要素改变对钉螺的影响方面已有较多研究，但有关生物要素与非生物要素对钉螺分布的交互作用还未有深入探索，对钉螺孳生产生抑制作用的关键要素尚不明确。文中综述了滩地造林后林下的草本植物群落、土壤理化性质、光照、地温等诸多要素发生变化对钉螺生存的不利影响，总结了滩地造林抑螺作用机理的研究进展，提出该领域今后的重点研究方向，以期为滩地造林抑螺作用机理的深入研究提供参考和借鉴。     

白果壳遗态HAP/C复合材料对水中氨氮的吸附

为综合利用农林废弃物，以白果壳为植物模板、羟基磷灰石（HAP）为改性材料，制备了白果壳遗态HAP/C复合材料（PBGC-HAP/C-G），并通过X射线衍射仪（XRD）、傅里叶红外光谱仪（FT-IR）和扫描电镜（SEM）等对其进行了表征，同时研究了溶液pH、初始浓度、吸附剂投加量等对其去除水中氨氮的影响。结果表明，PBGC-HAP/C-G是一种大孔材料，孔径主要介于35~200 μm之间。在溶液pH=5时，吸附效果最佳；吸附剂投加量的增加有利于氨氮的去除；粒径大小不是影响吸附效果的主要因素。准二级动力学模型和Freundlich等温吸附模型能很好地描述该吸附过程，吸附过程以化学吸附为主。在氨氮初始浓度为20、50、100 mg·L^-1时，拟合计算得到的理论平衡吸附量分别为0.45、1.10、2.15 mg·g^-1，与实验测定值0.46、1.15、2.18 mg·g^-1相近，可见PBGC-HAP/C-G可用作去除氨氮的吸附剂。     

Evaluation of limb autotomy as a promising strategy to improve production performances of mud crab (Scylla olivacea) in the soft‐shell farming system

Soft‐shell crab, a newly moulted crab having non‐calcified and hydrated soft exoskeleton, farming has been increasing tremendously in recent years throughout the world due to its high market price and consumer preferences. However, high aggressiveness and cannibalistic behaviour of mud crab limit its culture to an individual chamber system which ultimately makes the soft‐shell mud crab farming space and labour‐intensive. Therefore, the aim of this study was to improve the efficiency of soft‐shell crab production by autotomy of the claw and/or walking legs to reduce the moulting duration and intensify the culture system through double stocking in the existing individual chamber culture system. To achieve our objectives, a series of experiment were conducted at both indoor and on‐farm levels by removing the claw and/or walking legs of Scylla olivacea for two consecutive moulting cycles. Results showed that both claw ablation significantly (p < .01) shortened the moulting duration and increased the carapace width, weight gain, specific growth rate, feeding efficiency and yield parameter compared to the non‐ablated crabs more prominently at 1st moulting than the 2nd moulting in both indoor and on‐farm trials. Ablation of all walking legs while keeping the claw intact did not significantly influence (p > .05) the moulting duration and carapace width, but significantly (p < .01) improved the specific growth rate, weight gain, feeding efficiency and yield parameters at 1st moulting compared to the non‐ablation and unilateral three walking leg ablation groups. However, ablation of all appendages (both claw and walking legs) showed significant (p < .01) improvements of carapace width, weight gain, specific growth rate, feeding efficiency and yield parameters, and shortened the moulting duration up to 23 days from 34 days during 1st moulting and up to 27 days from 40 days at 2nd moulting. The survivals of different autotomized mud crabs were statistically non‐significant (p > .05) to the non‐autotomized crabs in various indoor and on‐farm trials. Besides improving the production performances, ablation of bilateral claw and all appendages allowed to double the stocking density in the existing individual chamber‐based soft‐shell crab farming that enhanced the production about threefold higher than the existing individual chamber‐based culture system. Finally, our results suggest that autotomy could be a promising technology for the commercial farming of soft‐shell mud crab in near future.     

大型薄壳制件真空辅助树脂传递模塑工艺充模方案仿真分析及优化

针对大型树脂基复合材料制件不适于用实验试错法进行充模方案设计的问题,在分析树脂流动规律的基础上将大型薄壳件的求解区域分解,仿真分析了不同充模方案下树脂在纤维中的流动行为和模腔内压力变化,提出在制件填充面积等分处设置流道的方法,选择和优化大型薄壳制件的充模方案。结果表明:①对于不便进行实验试错法进行真空辅助树脂传递模塑(VARTM)工艺充模方案设计的大型薄壳制件,可以采用数值模拟的方式,以达西定律、能量守恒定律等为计算依据,求解压力场和速度场,对比不同仿真方案的充模时间等数据合理安排注胶方式方法,指导VARTM工艺制备大型复合材料制件合理安排注胶方式,提高生产率、减少因树脂浸润不均匀产生的缺陷。②对于大型薄壳类制件,忽略厚度方向尺寸,影响充模时间的主要因素为流道长度和树脂流动距离。选取尽可能长的注胶流道,合理设置流道位置以减少树脂流动的距离;长流道可以增加树脂瞬时注入量、提高较长时间的压力差;而树脂流程越长,树脂前锋处压力损失越大,流速越慢。③试验提出了制件填充面积等分处设置流道的方法。将大型薄壳工艺制件充模面积等分,注胶流道布置在垂直于制件长度方向的面积等分线上,可缩短充模时间并减少制件两端的树脂富集现象。对于较狭长部分可再次进行面积等分设置流道,以免造成树脂流程过长压力流失过多;而对于较宽阔部分不宜设置过多流道以免树脂前锋稳定前互相接触造成制件充模不均匀。     

Pre‐Columbian fisheries catch reconstruction for a subtropical estuary in South America

Small‐scale fisheries provide food and livelihoods for thousands of people along the Brazilian coastline. However, considerable uncertainties still surround the extent to which artisanal and subsistence fisheries contribute to the total of national landings and their historical ecological significance. Fisheries monitoring is deficient in Brazil, and historical records are limited to irregular accounts spanning the last few decades, while this coastline has supported human populations for at least 6,000 years. Here, we estimate pre‐Columbian subsistence catches for a large subtropical estuary in southern Brazil. Our results suggest that prehistoric populations may have extracted volumes of fish biomass higher than or comparable with historical subsistence fisheries in the region, and that the latter is likely underestimated. If a long‐term perspective is required to evaluate the current economic value and status of fisheries in subtropical and tropical South America, this should go beyond the historical time interval and integrate the contribution of pre‐Columbian archaeology.     

基于茶籽壳代替木屑栽培茶树菇配方筛选试验

不同比例的茶籽壳和木屑组合成5个试验配方,比较不同配方对菌丝生长、子实体经济性状和生物转化率的影响。试验结果表明,在供试的5个配方中,配方4（棉籽壳50%、茶籽壳15%、木屑5%、麦麸20%、玉米粉7%、石膏1%、磷肥1%、石灰1%）为优选配方。     

融合光电色选的皮带筛式油茶果壳籽分选机设计与试验

针对油茶果批量脱壳后壳籽混杂、人力分选效率低的问题，研究设计了一种融合光电色选的皮带筛式油茶果壳籽分选机。根据油茶果壳、籽与倾斜传送带间摩擦角、碰撞系数的差异，设计振动皮带筛进行初分选；利用两者灰度差异，对壳中残留籽进行二次光电分选。对皮带筛上油茶果壳、籽进行运动学与动力学分析，发现皮带倾角、皮带速度和振动频率是影响振动初分选率的主要因素；以籽箱清洁率、壳中含籽率为试验指标，开展正交旋转组合试验。当皮带倾角为19°、皮带速度为1.50m/s、振动频率为55.40Hz时，其籽箱清洁率为95.52%、壳中含籽率为24.30%，对最优参数进行试验验证，优化结果可靠。对不同茶籽比率的物料进行光电分选试验，结果表明籽箱清洁率稳定在98.23%左右，壳中含籽率保持在2.34%左右，说明光电分选可准确识别并分选出混杂物料中的油茶籽。对整机进行最优参数试验验证，该机两籽箱茶籽平均清洁率可达97.55%，壳箱中含籽率为3.27%。试验结果表明，此油茶果壳籽分选机可实现油茶果壳、籽的高效分离。     

Phenotypic indicators for cultured pearl size improvement in the black‐lipped pearl oyster (Pinctada margaritifera): towards selection for the recipient growth performance

The black‐lipped pearl oyster, Pinctada margaritifera, is the most important farmed species in French Polynesia and the basis of the most valuable export industry. Mass production of black pearls relies on a surgical operation requiring tissue from a donor pearl oyster to be grafted, together with a nucleus made of shell, into the gonad of a recipient oyster. Improving pearl size through family selection remains one of the main challenges for future aquaculture development. This study analyses the relative contribution of donor and recipient oysters to pearl size. To this end, hatchery‐produced donor oysters of two batches, large and small (based on shell height), were used to supply grafts for recipients, which were then monitored individually for their growth performance by recording shell height, width, and thickness, and total live weight (flesh + shells) every 6 months (four biometric measurement times) over 20 months of culture. Pearls issued from the two batches of donors showed no significant differences in nacre weight or thickness. In contrast, recipient oyster shell height and total weight were increasingly positively correlated with these pearl size parameters over the culture period, becoming significant at 8 months post‐grafting. Potential therefore exists to use shell height and oyster weight as phenotypic indicators for selective breeding of recipient oysters with high growth performance to increase pearl size in P. margaritifera.     

滩涂互花米草除治技术研究

针对福建沿海滩涂外来物种互花米草疯长成灾问题,通过使用滩涂米草除控剂、种植秋茄等方法对互花米草进行除治技术研究,结果表明:在4-7月退潮后,用滩涂米草除控剂300-400 g稀水10 kg液均匀喷湿互花米草茎叶,2个月后叶枯根烂,次年4月下旬在除草迹地插植秋茄胚轴,幼树长势良好,为建设海峡西岸滩涂绿色屏障提供技术支撑.